Skip to main content
Inspection outcome
Opened: February 5, 2020 · Closed: April 4, 2022
Citations issued

OSHA issued one or more Other-than-serious citations.

Safety inspection · Type M · Partial — limited to specific operations or areas

Violations11
Serious+0
Initial penalty$41,240
Current penalty$15,384
Accidents0
Duration789d
Summary

What happened in this inspection

On February 5, 2020, OSHA opened Gamtex Industries Lp’s inspection #344607593 at FORT WORTH, Texas. The case was administratively closed on April 4, 2022, 789 days after opening.

OSHA cited the employer for 11 violations totaling $15,384 in current penalties — reduced from an initial proposed total of $41,240. All citations were Other-than-serious.

Breakdown by classification
11violations total
Serious1091%

A Serious violation is one where there is substantial probability that death or serious physical harm could result, and the employer knew (or should have known) of the hazard. Maximum penalty is ~$16,550 per violation. The majority of OSHA citations fall into this category.

Other-than-serious19%

An Other-than-serious violation has a direct relationship to job safety and health but probably would not cause death or serious physical harm. Maximum penalty is ~$16,550 per violation. Often involves recordkeeping or procedural lapses.

Citations

Citations issued in this inspection

11citations issued
$15,384current penalty
↓ $25,856total reduction
Look up on OSHA.gov
Seriousgravity 10
Citation #01001
5A0001General Duty Clause or unstructured citation
Initial$9,446
Current$5,668reduced by $3,778
Seriousgravity 5
Citation #01002A
29 CFR 1910.22(c)View full regulation text on OSHA.gov
Initial$6,747
Current$4,048reduced by $2,699
Seriousgravity 5
Citation #01002B
29 CFR 1910.22(d)(1)View full regulation text on OSHA.gov
Initial$0
Current$0
Seriousgravity 1
Citation #01003
29 CFR 1910.23(b)(9)View full regulation text on OSHA.gov
Initial$4,048
Current$2,429reduced by $1,619
Seriousgravity 5
Citation #01004A
29 CFR 1910.37(a)(3)View full regulation text on OSHA.gov
Initial$5,398
Current$3,239reduced by $2,159
Seriousgravity 5
Citation #01004B
29 CFR 1910.37(b)(1)View full regulation text on OSHA.gov
Initial$0
Current$0
Seriousgravity 5
Citation #01004C
29 CFR 1910.37(b)(2)View full regulation text on OSHA.gov
Initial$0
Current$0
Seriousgravity 5
Citation #01004D
29 CFR 1910.37(b)(4)View full regulation text on OSHA.gov
Initial$0
Current$0
Seriousgravity 5
Citation #01005
29 CFR 1910.145(c)(3)View full regulation text on OSHA.gov
Initial$5,398
Current$0reduced by $5,398
Seriousgravity 10
Citation #01006
29 CFR 1910.219(e)(1)(i)View full regulation text on OSHA.gov
Initial$9,446
Current$0reduced by $9,446
Other
Citation #02001
29 CFR 1910.101(b)View full regulation text on OSHA.gov
Initial$757
Current$0reduced by $757

Standard codes link to the regulation text on OSHA.gov. The text describes the rule itself; the specific findings of this inspection appear above. To see OSHA’s official record of this inspection, search activity number 344607593 at OSHA Establishment Search.

Same employer

Other OSHA inspections at Gamtex Industries Lp

Earlier or related cases at this establishment.

Full inspection history →
Reference

About OSHA inspections

The U.S. Occupational Safety and Health Administration (OSHA) conducts inspections under several triggers: programmed targeting of high-hazard industries, employee complaints, workplace accidents, fatalities, and follow-ups to prior citations.

📋
Citations

Each citation specifies a section of 29 CFR, a severity tier, and a proposed penalty. Employers can contest citations through OSHA’s informal conference or before the OSH Review Commission.

Open vs closed

An open case has not yet been administratively closed — citations may follow or the case may close without action.

💰
Current vs initial penalty

Initial penalty is the proposed amount at citation. Current penalty is the post-conference / settlement figure on file today.

🔗
Trigger types

A = Accident, B = Complaint, H = Programmed, F = Follow-up. See the glossary for all codes.

About this inspection

OSHA classified this as Type M — See our glossary for the full list of inspection trigger types.

Sources

Cross-check with OSHA directly

This page draws from the OSHA Integrated Management Information System (IMIS) via the DOL Open Data Portal. For the authoritative record, look up activity number 344607593 directly: