Skip to main content
Inspection outcome
Opened: November 18, 2025 · Closed: May 27, 2026
Citations issued

OSHA issued one or more Other-than-serious citations.

Health inspection · Referral · Partial — limited to specific operations or areas

Violations6
Serious+0
Initial penalty$144,240
Current penalty$72,120
Accidents0
Duration190d
Summary

What happened in this inspection

On November 18, 2025, OSHA opened The Mennel Milling Company’s inspection #348600677 at ALGER, Ohio. The case was administratively closed on May 27, 2026, 190 days after opening.

OSHA cited the employer for 6 violations totaling $72,120 in current penalties — reduced from an initial proposed total of $144,240. All citations were Other-than-serious.

Breakdown by classification
6violations total
Serious6100%

A Serious violation is one where there is substantial probability that death or serious physical harm could result, and the employer knew (or should have known) of the hazard. Maximum penalty is ~$16,550 per violation. The majority of OSHA citations fall into this category.

Citations

Citations issued in this inspection

6citations issued
$72,120current penalty
↓ $72,120total reduction
Look up on OSHA.gov
Seriousgravity 5
Citation #01001
29 CFR 1910.147(c)(7)(i)View full regulation text on OSHA.gov
Initial$14,188
Current$12,020reduced by $2,168
Seriousgravity 5
Citation #01002
29 CFR 1910.147(d)View full regulation text on OSHA.gov
Initial$14,188
Current$12,020reduced by $2,168
Seriousgravity 5
Citation #01003
29 CFR 1910.212(a)(1)View full regulation text on OSHA.gov
Initial$14,188
Current$12,020reduced by $2,168
Seriousgravity 10
Citation #01004
29 CFR 1910.272(g)(1)(iv)View full regulation text on OSHA.gov
Initial$16,550
Current$12,020reduced by $4,530
Seriousgravity 5
Citation #01005
29 CFR 1910.272(g)(5)View full regulation text on OSHA.gov
Initial$14,188
Current$12,020reduced by $2,168
Seriousgravity 5
Citation #02001
29 CFR 1910.272(g)(1)(ii)View full regulation text on OSHA.gov
Initial$70,938
Current$12,020reduced by $58,918

Standard codes link to the regulation text on OSHA.gov. The text describes the rule itself; the specific findings of this inspection appear above. To see OSHA’s official record of this inspection, search activity number 348600677 at OSHA Establishment Search.

Same employer

Other OSHA inspections at The Mennel Milling Company

Earlier or related cases at this establishment.

Full inspection history →
Reference

About OSHA inspections

The U.S. Occupational Safety and Health Administration (OSHA) conducts inspections under several triggers: programmed targeting of high-hazard industries, employee complaints, workplace accidents, fatalities, and follow-ups to prior citations.

📋
Citations

Each citation specifies a section of 29 CFR, a severity tier, and a proposed penalty. Employers can contest citations through OSHA’s informal conference or before the OSH Review Commission.

Open vs closed

An open case has not yet been administratively closed — citations may follow or the case may close without action.

💰
Current vs initial penalty

Initial penalty is the proposed amount at citation. Current penalty is the post-conference / settlement figure on file today.

🔗
Trigger types

A = Accident, B = Complaint, H = Programmed, F = Follow-up. See the glossary for all codes.

About this inspection

OSHA classified this as Referral — See our glossary for the full list of inspection trigger types.

Sources

Cross-check with OSHA directly

This page draws from the OSHA Integrated Management Information System (IMIS) via the DOL Open Data Portal. For the authoritative record, look up activity number 348600677 directly: