Skip to main content
Inspection outcome
Opened: October 28, 2020 · Closed: December 29, 2022
Citations issued

OSHA issued one or more Other-than-serious citations.

Safety inspection · Planned (Programmed) · Partial — limited to specific operations or areas

Violations10
Serious+0
Initial penalty$32,385
Current penalty$6,477
Accidents0
Duration792d
Summary

What happened in this inspection

On October 28, 2020, OSHA opened Technique Manufacturing Inc’s inspection #344998570 at HUTCHINSON, Kansas. The case was administratively closed on December 29, 2022, 792 days after opening.

OSHA cited the employer for 10 violations totaling $6,477 in current penalties — reduced from an initial proposed total of $32,385. All citations were Other-than-serious.

Breakdown by classification
10violations total
Serious990%

A Serious violation is one where there is substantial probability that death or serious physical harm could result, and the employer knew (or should have known) of the hazard. Maximum penalty is ~$16,550 per violation. The majority of OSHA citations fall into this category.

Other-than-serious110%

An Other-than-serious violation has a direct relationship to job safety and health but probably would not cause death or serious physical harm. Maximum penalty is ~$16,550 per violation. Often involves recordkeeping or procedural lapses.

Citations

Citations issued in this inspection

10citations issued
$6,477current penalty
↓ $25,908total reduction
Look up on OSHA.gov
Seriousgravity 5
Citation #01001
29 CFR 1910.110(f)(6)(ii)View full regulation text on OSHA.gov
Initial$3,856
Current$771reduced by $3,085
Seriousgravity 5
Citation #01002
29 CFR 1910.178(l)(6)View full regulation text on OSHA.gov
Initial$3,856
Current$771reduced by $3,085
Seriousgravity 10
Citation #01003
29 CFR 1910.212(a)(3)(ii)View full regulation text on OSHA.gov
Initial$5,398
Current$1,080reduced by $4,318
Seriousgravity 5
Citation #01004
29 CFR 1910.212(b)View full regulation text on OSHA.gov
Initial$4,626
Current$925reduced by $3,701
Seriousgravity 5
Citation #01005A
29 CFR 1910.219(d)(1)View full regulation text on OSHA.gov
Initial$4,626
Current$925reduced by $3,701
Seriousgravity 1
Citation #01006
29 CFR 1910.1200(f)(6)(ii)View full regulation text on OSHA.gov
Initial$2,313
Current$463reduced by $1,850
Seriousgravity 1
Citation #01007
29 CFR 1910.1200(g)(1)View full regulation text on OSHA.gov
Initial$2,313
Current$463reduced by $1,850
Seriousgravity 5
Citation #01008
29 CFR 1910.1200(h)(1)View full regulation text on OSHA.gov
Initial$4,626
Current$925reduced by $3,701

Standard codes link to the regulation text on OSHA.gov. The text describes the rule itself; the specific findings of this inspection appear above. To see OSHA’s official record of this inspection, search activity number 344998570 at OSHA Establishment Search.

Reference

About OSHA inspections

The U.S. Occupational Safety and Health Administration (OSHA) conducts inspections under several triggers: programmed targeting of high-hazard industries, employee complaints, workplace accidents, fatalities, and follow-ups to prior citations.

📋
Citations

Each citation specifies a section of 29 CFR, a severity tier, and a proposed penalty. Employers can contest citations through OSHA’s informal conference or before the OSH Review Commission.

Open vs closed

An open case has not yet been administratively closed — citations may follow or the case may close without action.

💰
Current vs initial penalty

Initial penalty is the proposed amount at citation. Current penalty is the post-conference / settlement figure on file today.

🔗
Trigger types

A = Accident, B = Complaint, H = Programmed, F = Follow-up. See the glossary for all codes.

About this inspection

OSHA classified this as Planned (Programmed) — a programmed (planned) inspection, typically targeting high-hazard industries.

Sources

Cross-check with OSHA directly

This page draws from the OSHA Integrated Management Information System (IMIS) via the DOL Open Data Portal. For the authoritative record, look up activity number 344998570 directly: